Mirror of /pweb.jps.net/~snowbum/luftmstrtanks.htm

This is a mirror of http://pweb.jps.net/~snowbum/luftmstrtanks.htm.
It is provided here by cdegroot.com to increase availability of the original site. This mirror is updated daily so should be up-to-date at all times.

These particular tanks fit many of the LWB airhead models, but NOT the SWB R65/R45...or so I thought, and per my Luftmeister catalog. But, in 2005 I was informed that some WERE made for the R65/45, with either the backside being a plate cover, or some sort of plate covering the fuse area...I have never personally seen these, only heard of them from one person.

All the Luftmeister auxiliary fuel tanks are made of aluminum alloy, and the ones other than the R65/R45 hold approximately 1 gallon plus 8 ounces of gasoline, if filled to the brim (NOT recommended by me). The R65/R45 MAY hold the same, I have NO information on them.....all information that follows refers to the larger engine Airhead tanks, as I am very familiar with them. NOTE: The R65 in the 80's had the larger displacement size of rear subframe. It is my guess that the Luftmeister tanks for all the models other than the R45/R65 will probably fit those larger frame R65 just fine.

These tanks were originally produced with static electricity discharge foil strips called Explosafe, stuffed inside. The stuff looks like silvery metal as might come out of an office paper shredder. Removing that material, or much of it, which does not seem to have any great safety features, allows only a tiny amount additional fuel.

The tank petcock valves were mostly of a type that were equipped with a knurled knob, and those valves incorporated a fuel screen that sticks up into the tank, just like some of the BMW valves, but on a smaller scale. More than one type of valve has been fitted. Some valves have peg handles too easily knocked off by passenger's feet, those handles can be easily shortened. The packing material on at least one type of the valves is replaceable, and the adjustment nut can be set for smooth knob operation.

The upper tank port, as well as the bottom port containing the valve, was designed to be plumbed into the Airhead fuel system as a CLOSED system, thereby avoiding noxious vapors that might tend to annoy the rider, due to the vacuum effect that motorcycles tend to create in the rider area.

Use (preliminary) and Venting Considerations:
NOTE: it is quite possible to install only ONE of these Luftmeister tanks, if that is what you want to do.

Using these tanks requires some definite thought and care. If the main tank valves are improperly used, you can cause the Luftmeister tank seams to split when they are quite full, since liquid does not compress like an airspace does. This can happen from the motorcycle sitting in the sun. The proper usage is likely to just leave the Luftmeister tank valves turned ON all the time, except when stored in your garage. Whilst riding, you can, of course, leave the Luftmeister tanks turned on, all the time, or not....but, if properly installed, they will always be 'vented' INTO the Airhead fuel system.

For garage storage, I recommend using only the center stand, and also closing the main tank valves, and then loosening the Luftmeister side tank caps a bit, perhaps a couple of turns, and closing the Luftmeister valves. This will almost totally eliminate any possibility of a dangerous leaking condition from the carburetors (from a bad float bowl needle), which can cause a fire, explosion, etc. Many folks have gas fired water heaters in their garages, or electrical switches...etc. You must remember to lightly tighten the auxiliary tank caps before riding off. There is a fair amount of fuel left in the lines and filter above the carburetors, so any serious leak from the carburetor, usually a faulty bowl in some way, or a faulty float needle, should be addressed immediately.

When filling up at a gas station, I HIGHLY recommend closing the main tank valves briefly during filling of the main and side tanks.

These tanks were designed by Luftmeister to be used in a closed system, with no external venting. At one time they had other ideas. Matt Capri said he designed these tanks for a sort-of similar closed system as I described, per a talk I had with him. I have tried other venting methods. I really did not want a closed system due to the careful watch you must make on all the above mentioned valve and cap operations. In particular I tried just running the Luftmeister valve outputs to a T at the carburetors, and ran the upper Luftmeister vent connections to a common T and thence to the existing BMW tank venting hose under the tank. This resulted in BAD fumes, especially from a siphoning effect! I then tried combinations of running a hose up high (to top of windshield!), but still could not eliminate the problems. I determined that almost 3 feet higher was necessary. I suspect Luftmeister found the same problems. I think they also experimented with vented caps. The closed system works fine, but you MUST remember the cautions on using the main tank petcocks, etc.

Installation Details:

The proper installation is as follows, and I will describe the left side, the right side is identical:
Fit the tanks in mockup form first. Be sure they fit as the clamps may not be shaped just right, and you may very well want to line the two clamp areas with rubber, so the tanks fit better. It is important to keep the mounting of the tanks as high as possible. If they are NOT mounted quite high enough, you will NOT be able to use all their contents. After you fit them, and bolt them to the BMW rear subframe area, you are ready to install the plumbing. NOTE that the outlet valves must either have the internal screens sticking up into the tank, or, an external small fuel filter. SOME folks use BOTH. I do. I also put rubber onto the tanks clamp areas.

For fuel filters, this is the ONE place I use the smallest of the plastic aftermarket folded paper-containing filters. Install them in a convenient position in the hose from the tank petcocks. Remember that if you run that hose upwards, then you will NOT be able to fully use the Luftmeister tanks contents! I prefer BMW black rubber FUEL hose for the installation, but you can use the silver Bing/BMW hose, or even aftermarket American hose, although the outside diameter of MOST American hose is larger....which is why the stock left-right hose through the aircleaner housing area does not usually fit well if it is American. Use ONLY FUEL HOSE!! I highly recommend against cheap clear plastic fuel line ...it hardens! There are industrial quality plastic lines that do not.

From the main tank on/off/reserve petcock valve, connect a METAL (preferred) BMW gas line "T", rather close to the main tank petcock valve, using an 'arm' of that T and hose as required. The BMW metal T fittings are about $4 each and are #13-11-1-336-900. The other 'arm' goes, via hose, to the 90 degree fitting of the TOP outlet/inlet area of the Luftmeister. You will need two more of the metal T fittings for this side, and some more hose. From the first T mentioned above, the NON-arm goes downward to another T, its arm. The other arm of that 2nd T goes downward to a final T arm and the final T arm goes to the lower valve outlet of the Luftmeister.

This leaves you with two each NON-arms to finish: the NON-arm of the middle T goes to the old crossover rubber hose that leads to the right side of the machine. The lowest T non-arm goes to the carburetor. It is important that the lowest of the three T fittings that goes to the carburetor (non-arm outlet) is as low as possible, so use a really short section of rubber hose. If this is not low enough, you will not get all the gas from the side tanks.

I prefer to use BMW's latest rubber hose, not American hose, not the old silver woven hose. I have used Industrial plastic hose, and it is fine too. This is, of course, your choice. Use of hose clamps are optional, and may not be needed with some types of hose. I found them mostly unnecessary, although I used them at the Luftmeister TANK fittings, due to the SHAPE of the particular fittings I used there.

I HIGHLY recommend installing fuel filters. The best setup is to install one at each main tank outlet, and one in line with each Luftmeister tank outlet hose. The common clear plastic cased paper element filters work very well. The smallest ones work fine for the Luftmeister tank outlet hose, but I prefer a larger one for the main tank outlet. These are available from NAPA, and most other autoparts stores. The plastic nipples on these are slightly fragile (cracking possible if under side pressure), so install them carefully. I have nothing against your use of other types of these filters.

Turn OFF your main tank valves. Fill the main tank. Remove caps of Luftmeister tanks, fill to about an inch below the top threads. Do NOT fill to the brim. Install the Luftmeister caps, which may be drilled by Luftmeister along the knurled edge, and SEEM to look vented... but the caps ARE NOT VENTED, and are sealed with a plate, screw, ETC...as shipped. The caps have a rubber O ring to seal them to the tanks. Replacements can be any common type....see NOTES 3, end of this article, for information.

After filling the tanks, IMMEDIATELY turn the main tank, one or both valves, ON, in accordance with your normal riding habits...which you may want to change to both valves being on.    At this point you can turn on the Luftmeister valves themselves on if you want to.

IF the bike is parked in the sun the heating of the side tanks will cause the gasoline in them to rise slightly, compressing the air space you left, and no problems will occur. If the tanks heat enough and the level was high enough, the expanding gasoline would move UPwards INto the main tank, since the main tank valve(s) are turned on...still no problems. Even if only one main tank valve is turned on, the crossover hose will allow the auxiliary tanks to vent properly to the main tank. IF you turn off the main tank petcocks, the pressure can continue to rise in the Luftmeister tanks....and either overpower the carburetor float needle (not usually likely), or split a Luftmeister tank seam, or? Thus, the reason I say to either not turn off the main tanks during storage, or, better, turn them off and then unscrew the Luftmeister caps a bit (main tank OFF).   Think over carefully what I am saying here.....NOW do you see why I said NOT to totally fill the Luftmeister's?...liquid will not compress!

Parking/storing the bike in your garage....or wherever:
FIRSTLY, a caution: it is best to use the center stand and NOT the sidestand; otherwise, the right side tank can transfer gasoline to the left side, causing overflow, if caps are loose. This CAN happen even if the right side tank is nowhere's near full....and its valve is open.   Turn main tank valves OFF. Turn Luftmeister valves OFF. LOOSEN Luftmeister filler caps a few turns. This will NOT work if the Lufty's have a lot of gas in them and you are using the side stand...the right Luftmeister will feed the left, and you'll have gas all over the place.

****If you must use the sidestand, leave the main tank valves on, and the Luftmeister caps tight. Better yet, for sidestand use and safety purposes if in your garage for STORAGE purposes, drain the Lufty's and leave the main tank valves off.   Remember that gasoline fumes in enough concentration can make for a large bomb.....and light switches in your garage, static electricity, water heaters, etc.....can ignite the fumes. Be cautious!

On-the road, for automatic feeding, and keeping your original main tank reserves, but adding the approx. 2 gallons in the Luftmeisters for use,. simply turn BOTH main tank valves ON (levers DOWN) AND turn on BOTH Luftmeister valves. Ride until you need reserves, then turn main tank valves to reserve, just like you always have, one at a time if you want to; or, both at once.  Any combination of using mains, sidetanks, reserves, etc., is OK with me, so long as YOU understand all implications!

NOTES 1:

   The Luftmeisters are in a CLOSED system. When a main tank side runs dry on any side, in any main tank valve position (except OFF), the main tank then becomes the VENT for the Luftmeisters, allowing the Luftmeisters to operate "automatically".

Do not remove all of the 'Explosafe' material in the Luftmeisters.   While it is PROBABLY safe not to have ANY, it takes up very little actual liquid equivalent volume. I generally take about 3/4 of it out. ALL of it uses about a cup's worth of gasoline at the most.

NEVER park your bike in the sun with the main tank valves turned off...the side tanks will pressurize and may burst a seam or leak at a fitting, well before the pressure overcomes the carburetor needle/seat seal pressure. The leaving of a small air space in the top of the Luftmeister tanks may help some, but do NOT depend on this!   I had one of my carburetors develop the usual 'tad of dirt in the float needle area' at a campout some years ago (Bad to the Beach campout). I had left the Luftmeister valves closed, main tank valves ON...like I usually do when out someplace. Some kind soul caused my extensive painting and prep effort on my Luftmeisters to go bye bye when he 'kindly' turned off my main valves to stop my leak. So, be warned about how you use the valves, caps, etc.

The Luftmeister CAPS are sometimes found drilled for venting, but sealed over, sometimes with a screw....or the machining incompleted. They must be not be vented. The original cap rubber O-ring can be replaced with a somewhat thinner version, such as the Napa R-26, which is 34.5 mm ID and 3.5 mm thick. Remember: The CAPS are NOT vented, although they might look that way...I think the caps were made with venting in mind, then that was not actually done. My experiments showed that Luftmeister probably had venting problems during the design, and that is why they went to a closed system.

Revisions:
04-17-2003: add .htm title; clarifications, minor
02/27/2005: clarifications, add NOTES 2.
10/12/2005: slight updates and clarifications
02/15/2007: slight updates on R65/R45; add keywords, content, description, all as Meta information
04/01/2008: Re-arrange article somewhat, and edit here and there and add NOTES 3